If you have a little bird and you want to make a cute looking nest for the bird, then you might want to simply try the DIY bottle bird house. That is because this kind of birdhouse can be considered as one unique thing that your little bird will surely love. As an addition to that, you will not need a lot of money to make this kind of birdhouse. If you are thinking about the same thing, then you just need to follow all of these steps below to make your own birdhouse from the used bottle.
Best Bottle for Birdhouse
For the beginning, you will need to take a used bottle for the birdhouse. When you are choosing the bottle, you will need to make sure that you are using the plastic bottle. That is because if you are using the glass bottle, you will not be able to cut the centre parts of the bottle for the entrance for your little bird. As an addition to that, you will need to make sure that the size of the bottle is big enough so that your bird can easily enter the DIY bottle bird house. If you think that your bird is too big for the biggest plastic bottle that you can find, then it will be useless to make the birdhouse using the bottle. It will be better for you to buy the real bird nest rather than making the DIY project for your bird.
Picking the Best Entrance for Birdhouse
If you have prepared the plastic bottle, you will need to draw a circle on the lower part of the bottle. The location should be around two inches from the bottom part of the bottle. This one is important so that you can put the proper amount of feather as the base for your bird to sleep. If you making the entrance too high, you will need a lot of fur for the base for your bird to sleep and that might be a little bit hard to do. On the other hand, if you make the entrance too low from the bottom, you will end up with very few feather on the DIY bottle bird house that will not give any comfort at all to your little bird. Therefore, you should be careful. As an addition to that, when you are drawing the circle, you need to make sure that the size of the circle is big enough so that your bird can easily go in and out from that entrance. The average of two to three inches circle is enough to do the trick. After you have drawn the circle, then you will need to cut that part. You can use scissor, cutter, or anything as long as you can make the hole in that part of the bottle.
Hanging the DIY Birdhouse
The next thing that you need to do after you have finished with the entrance is to deal with the hanger. If you want to hang the birdhouse, you will need to start by drilling the top cap of the bottle. Make sure you have two small holes on the top of your DIY bottle bird house. That is because those two holes will be used for the wires that you can use to hang the birdhouse later on. For your consideration, two a millimeter holes are enough to do the trick. However, you will need to pick the strong wires to hang the birdhouse. For your consideration, it will be better for you to pick the stainless steel wire so that you will not need to deal with the corrosion if you have to leave the birdhouse outside in the middle of the rain for days. For the finishing, set the proper length of the wire and try to hang the birdhouse first before you continue to the next step.
Roof Tile Finishing Using Old CDs
If you have finished with that, you will need to get some old and used CDs for the main decoration on the birdhouse. You will need at least five to ten CDs to create the nice looking tile roof for the DIY bottle bird house. To do that, you will need to cut the CDs into six to eight pieces equally. That is because all of those small CD pieces will be used as the tile roof on the top part of the bottle. To do that, you need to glue all of those pieces one by one and create the kind of roof tile impression from all of those pieces. As an addition to that, you need to also make sure that you put the shiny bottom part of the CD facing up so that you will be able to have the kind of shiny impression when the sun shines on the birdhouse.
Painting for the Final Touch of the Birdhouse
If you have finished making the roof tile for the birdhouse, then you just need to simply paint all of the parts of the bottle. The paint is used to make sure that you can have the nice looking birdhouse for your little bird. Basically, you can use any kind of color for your birdhouse, but it will be better for you to pick the kind of color that can easily blend with the surrounding where the DIY bottle bird house will be placed. For example, if you want to put the birdhouse on the tree, then something green will do the trick. On the other hand, if you want to put the birdhouse on top of your front door with brown paint, then something brownish will do the trick perfectly.
Those are some simple steps that you can try if you want to make the birdhouse on your own. For your information, those steps below can be considered as the basic steps that you need to follow if you want to make the DIY bottle bird house. If you want something more attractive, then you can try to add some windows on the birdhouse or even adding some other entrance and hanging base for your little bird to hang outside the house.
- how to make bird house
- how to make birds house